5400R zl2 V3 switch Group Table in hardware
Hello, I'm using HP 5400R zl2 V3 switch. It is suppose to have group table in hardware. I found in the KA16.01 Administrator Guide that group type "ALL" is supported in hardware. I don't quit...
View ArticleFlow-mod fails on HP 2920-24G: Error code EPERM
Hi,I am using an HP 2920-24G/ J9726A switch. I upgraded the firmware to WB.16.02.0012. I created an aggregate instance with version 1.3 and was successfully connected to a floodlight controller....
View ArticleMachine Learning in SDN
I am Working on SDN Controller. I want to implement Machine Learning Algorithm on SDN Controller how it should be Implemnted Kindly Guide me. Thanks
View ArticleOpendaylight basic question
I am new to Opendaylight and SDN. I have installed Opendaylight Oxygen 0.8.4 in my Ubunutu. I also installed the feature packages e.g. odl-restconf-all odl-l2switch-all odl-dlux-core in Opendaylight....
View ArticleConnect MATLAB simulink model to the real physical SDN-based switches
Dear all, How can I connect my MATLAB software model including simulink and script codes to a real physical server (not virtual Mininet) with software-defined networking (SDN) switches? The server...
View ArticleMonitor VTEP packet
This is not quite SDN question but still closely related to SDN because when we are talking about the concept of "SDN via hypervisor virtualization", then topic of VTEP constantly is touched.I am...
View ArticleOpenflow HP ProCurve 6600-24g-4xg
Hi,I'm Msc student on faculty of electrical engineering. I have to create an OpenFlow testbed which might be consisted of more Openflow instances. So, could anyone tell me is it possible to configure...
View ArticleMetering in Software Tables HP 2920
Hi,I am using HP2920, WB.16.02.0012. I wanted to create a meter entry in table 200 and was surprised that it does not support metering, is that correct ? Is table 100 the only table that supports...
View ArticleExtending FlowTrk class
Hello,is there a way I can extendcom.hp.of.ctl.flow.impl.FlowTrk?My HP-specific dependencies are: com.hp.sdn.sdn-of-lib, com.hp.sdn.sdn-of-ctl, com.hp.sdn.sdn-ctl-apicom.hp.of.ctl.flow.impl.FlowTrk is...
View Articlesudo apt-get -f install ERROR
https://www.youtube.com/watch?v=gaBSHna8v4E&t=337s following these videos step by step, however when i do the sudo apt-get -f install it goes through the install but ends with Done!Failed to start...
View ArticleI am unable update my HPE Net Protector RepDV licence
Hi AllAny ideas for the problem below, I cannot find any online troubleshooting on thisThank youBarry--------Problem: I am unable update my HPE Net Protector RepDV licenceI have done the following:My...
View ArticleThreads in HP-VAN
Hi, I want to develop a module for HPVAN 2.7.0 that uses threads to collect counters from switches. Under my model, a flow is constituted by a Match and a list of DPIDs. What I want to do is to let...
View ArticleHP ProCurve 6600-24g-4xg
Hi guys,Can anyone tell me is it possible to change flow location from 'software' to 'hardware and software' in OpenFlow v1.0? Beceuse, in software mode is possible to forward only 100 pps by default,...
View ArticleWant to use hardware flow-table on my HPE Openflow switch
Hi,I want to use hardware flow-table on my HP openflow switch, but when I type command flow-location hardware-only, I get next message on the controller:[openflow.of_01 ] [2c-41-38-1b-43-80|30 8]...
View ArticleHow to listen to MESSAGE_TX Events
Hi, My application is able to listen to Error Messages by implementing the MessageListener interface. Whenever an error occurs due to FLOW_MOD_FAILED#TABLE_FULL I am able to get the RX message and...
View ArticleUsing Hardware flows-table with hp 2920 24g
Hi,I am using an HP 2920 24g (J9727A) switch as an OpenFlow switch. I have 3 PCs connected to this switch:- PC1 : Beacon controller as SDN Controller- PC2 and PC3 : Hosts in the Data Plane My switch...
View ArticleOpenFlow capability differences between new Aruba's (2930F, 3810, 5400R)
Hi,I'm looking at the new Aruba switches (2930F, 3810, 5400R) for OpenFlow development, and in particular their custom pipeline support.Is there a difference between between them other than backplane...
View ArticleTroubles setting up Visualizer with 3810
Hi!We're having some troble getting Network Visualizer work with 3810 switches. We have this really simple setup; two hosts connected to the switch and a HP VAN controller using oobm.When we try to...
View ArticleClik here to view.
Questions about the steps to create a simple SFC ?
I am a newbie for join ODL.I need to create a SFC.This is my simple sfc topology.I tried to understand odl sfc104 how to building a sfc on my physical machine.And then install...
View Article